Cisco Router ****ie

[م/ أحمد بخيت]

السلام عليكم
لو سمحت انا كنت عاوز الطريقة اللي اقدر بيها ابني الكوكي بتاعة الراوتر C1600 الراوتر كان عندي وكنت عامل بيه لاب مع راوتر C3620
لكن الراوتر C1600 لقيته بيطلع رسالة بتقول ان الكوكي وقع
انا عملت ريستارت ودخلت الامر Priv
طلب مني شفرة
مش عارف اكمل اعمل ايه ؟؟؟

[م/ أحمد بخيت]

ايه يا جماعة معقول ولا رد
طيب انا كنت عاوز اظبط العطل دا لوحدي
ومش عاوز اوديه الضمان
ع العموم انا ف الانتظار

[frozenEyes]

جرب الرابط التالى :
https://www.tech-recipes.com/rx/982/recovery-eprom-****ie-on-router-cisco/

وهذة معلومات عن C o o k i e
https://www.bitshift.ch/eng/support/kbase/000001.asp

وبالتوفيق ان شاء الله ،،،

[م/ أحمد بخيت]

جرب الرابط التالى :
https://www.tech-recipes.com/rx/982/recovery-eprom-****ie-on-router-cisco/

وهذة معلومات عن C o o k i e
https://www.bitshift.ch/eng/support/kbase/000001.asp

وبالتوفيق ان شاء الله ،،،


مشكور اخي الكريم
لكن الرابط الأول مش عشان سيسكو
والتاني مش بيقدم معلومات عن شفرة الكوكيز
لكن ممكن اعرف ازاي امسح الكوكيز وانا اعرف اكمل بعد كدا ؟؟؟

[frozenEyes]

Recovery EPROM ****ie on Router Cisco (https://www.tech-recipes.com/rx/982/recovery-eprom-****ie-on-router-cisco/)


The router will be in ROMMON status, so don’t try to use the TFTPDNLD command or XMODEM to load the IOS because it’s still in the Flash.
Here’s the steps to follow to repair the router:
1- in the rommon mode digit the command PRIV that allows to you to enter in the privileged mode, use the password 0000 (four zeros) and enter.

2- if you ****ies are corrupt you’ll see this situation:
>>rommon 1 > ****ie
>>WARNING: ****ie information is corrupt
>>
>>****ie:
>>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>>rommon 2 >

3- now type the command ****IE so you can set the values manually.When you insert them you just need to insert the values after the :
Below you can see good ****ies of a 827 router:

byte 0×00 – Version: 01
byte 0×01 – Vendor (Recommended Value: 0×01): 01
bytes 0×02-0×07 – Ethernet HW Address: 00 04 27 fe 00 ea
byte 0×08-0×08 – Processor (Recommended Value: 0×3e): 3e (0×3E for 827
e_machine=62)(0×5B for soho77 e_machine=91)
byte 0×09-0×09 – NVRAM Size (Recommended Values: 256K – 0×00): 00
byte 0×0a-0×0a – CPU Speed (Recommended Value: 50Mhz – 0×01): 01
byte 0×0b-0×0b – Unused: ff
bytes 0×0c-0×0d – On-board PM ID: 01 ff
bytes 0×0e-0×0f – MAC Address Allocated: 00 00
bytes 0×10-0×17: 00 00 00 00 00 00 00 00
bytes 0×18-0×22: 4a 41 44 05 42 30 39 ** ** 03 01 (Processor board ID
JAD054209**)+(CPU revision 0×301)
bytes 0×23-0×24 – Deviation: 6f e6 (hardware revision 6FE6)
bytes 0×25-0×2c: 00 00 00 00 ff ff ff 50 (50 should be cpu_type)
bytes 0×2d-0×2d – Board Config: 04
bytes 0×2e-0×31: 49 11 ec 03
bytes 0×32-0×37 – WAN MAC Address: ff ff ff ff ff ff
bytes 0×38-0×3f: ff ff ff ff ff ff ff ff
bytes 0×40-0×47: ff ff ff ff ff ff ff ff
bytes 0×48-0×4f: ff ff ff ff ff ff ff ff
bytes 0×50-0×57: ff ff ff ff ff ff ff ff
bytes 0×58-0×5f: ff ff ff ff ff ff ff ff
bytes 0×60-0×67: ff ff ff ff ff ff ff ff
bytes 0×68-0×6f: ff ff ff ff ff ff ff ff
bytes 0×70-0×77: ff ff ff ff ff ff ff ff
bytes 0×78-0×7f: ff ff ff ff ff ff ff ff

As i told you the important values are number after the : as you can see let’s see the first two rows of the previous example :

byte 0×00 – Version: 01 —–> insert only 01
byte 0×01 – Vendor (Recommended Value: 0×01): 01 —> insert 01
and the same for all the others rows.

The final situation of the ****ies will be something like this:

01 01 00 b0 c2 8e 5e 81 5b 00 01 ff 01 ff 00 00
00 00 00 00 00 00 00 00 4a 41 44 05 31 30 50 38
33 04 01 00 00 00 00 00 00 ff ff ff 50 04 49 11
ec 04 ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

(these are exact ****ies for a soho77)

At the end you just need to reset your router and your IOS and configuration will be there ready to work again.



ملاحظة : اى علامة **** ضع مكانها كلمة c o o k بس بدون المسافات لان الموقع هنا بيحذفها،،

[م/ أحمد بخيت]

مشكور أخي الكريم ع المتابعة والرد كمان
لكن انا كنت عاوز طيب ازاي امسح الكوكي عشان الشفرة تكون 0000