مشاهدة النسخة كاملة : اريد كسر سرعه معالجي i7 980x
السلام عليكم
ارغب في كسر سرعه معالجي انا جديد بالكسر وتعديل البايوز
الصندوق haf x بكامل مراوحة 4 مراوح
والمشتت H70
هذه الصور
https://www.freeimagehosting.net/uploads/7cca6242a3.gif
https://www.freeimagehosting.net/uploads/438877c0a0.gif
https://www.freeimagehosting.net/uploads/5ce3786196.gif
https://www.freeimagehosting.net/uploads/f2a13d86fd.gif
https://www.freeimagehosting.net/uploads/4ab2308de2.gif
https://www.freeimagehosting.net/uploads/bb0df97ccb.gif
Extreme2
17-04-2011, 20:11
عليكم السلام
ياريت صورة لدرجات الحرارة أثناء الضغط لمدة 15 دقيقة ببرنامج Prime95 .
Ahmed Elbrbry
17-04-2011, 21:52
اليك BIOS TEMPLATE للوحة الخاصة بك
لتسهيل التعامل مع المسطلحات
Target CPU Frequency 2666MHz
Target DRAM Frequency 1603MHz
LN2 Mode: Disabled***
QPI Loadline Calibration: Enabled
***Sync Mode [Enabled]
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [20.0]
CPU Turbo Power Limit [Disabled]
CPU Configuration
CPU Ratio Setting [20.0]
C1E Support [Enabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetcher [Enabled]
Intel(R) Virtualiyation Tech [Enabled]
CPU TM Function [Disabled]
Execute Disable Bit [Enabled]
Intel(R) HT Technology [Enabled]
Active Processor Cores [All]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Enabled]
Intel(R) C-STATE Tech [Enabled]
C State package limit setting [Auto]
BCLK Frequency [133]
PCIE Frequency [100]
DRAM Frequency [1603]
UCLK Frequency [3209]
QPI Link Data Rate [AUTO]
Memory Configuration Protect [Disabled]
>
DRAM Timing Control
CAS# Latency 9 [9]
RAS# to CAS# Delay 9 [9]
RAS# PRE Time 9 [9]
RAS# ACT Time 24 [24]
RAS# to RAS# Delay 6 [AUTO]
REF Cycle Time 110 [110]
WRITE Recovery Time 15 [15]
READ to PRE Time 9 [9]
FOUR ACT WIN Time 31 [31]
Back-To-BackCAS# Delay 0 [Auto]
Timing Mode 1N [1N]
Round Trip Latency on CHA [AUTO]
Round Trip Latency on CHB [AUTO]
Round Trip Latency on CHC [AUTO]
WRITE To READ Delay(DD) 8 [Auto]
WRITE To READ Delay(DR) 8 [Auto]
WRITE To READ Delay(SR) 18 [Auto]
READ To WRITE Delay(DD) 7 [Auto]
READ To WRITE Delay(DR) 7 [Auto]
READ To WRITE Delay(SR) 7 [Auto]
READ To READ Delay(DD) 7 [Auto]
READ To READ Delay(DR) 6 [Auto]
READ To READ Delay(SR) 4 [Auto
]WRITE To WRITE Delay(DD) 8 [Auto]
WRITE To WRITE Delay(DR) 8 [Auto]
WRITE To WRITE Delay(SR) 18 [Auto]
CPU Differential Amplitude [Auto]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
Extreme Engine Digi
Digi+ PWR Mode [T-Balanced]
PWR Volt. Control [Auto]
Load-Line Calibration [Full]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [1000kHz]
Extreme OV [Disabled]
Extreme OC [Auto]
CPU Voltage 1.250 [1.25000]
CPU PLL Voltage 1.812 [Auto]
QPI/DRAM Core Voltage 1.350 [1.35000]
DRAM Bus Voltage 1.654 [Auto]
>DRAM REF Voltages
DRAM DATA REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM DATA REF Voltage on CHB [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHC [Auto]
DRAM CTRL REF Voltage on CHC [Auto]
IOH Voltage 1.244 [Auto]
IOH PCIE Voltage 1.508 [Auto]
ICH Voltage 1.111 [Auto]
ICH PCIE Voltage [Auto
]
Spread Spectrum Control
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
***on-board jumper dependant
عليكم السلام
ياريت صورة لدرجات الحرارة أثناء الضغط لمدة 15 دقيقة ببرنامج Prime95 .
شكرا لك على الرد
https://www.freeimagehosting.net/uploads/b9b95cdc05.gif
اليك BIOS TEMPLATE للوحة الخاصة بك
لتسهيل التعامل مع المسطلحات
Target CPU Frequency 2666MHz
Target DRAM Frequency 1603MHz
LN2 Mode: Disabled***
QPI Loadline Calibration: Enabled
***Sync Mode [Enabled]
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [20.0]
CPU Turbo Power Limit [Disabled]
CPU Configuration
CPU Ratio Setting [20.0]
C1E Support [Enabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetcher [Enabled]
Intel(R) Virtualiyation Tech [Enabled]
CPU TM Function [Disabled]
Execute Disable Bit [Enabled]
Intel(R) HT Technology [Enabled]
Active Processor Cores [All]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Enabled]
Intel(R) C-STATE Tech [Enabled]
C State package limit setting [Auto]
BCLK Frequency [133]
PCIE Frequency [100]
DRAM Frequency [1603]
UCLK Frequency [3209]
QPI Link Data Rate [AUTO]
Memory Configuration Protect [Disabled]
>
DRAM Timing Control
CAS# Latency 9 [9]
RAS# to CAS# Delay 9 [9]
RAS# PRE Time 9 [9]
RAS# ACT Time 24 [24]
RAS# to RAS# Delay 6 [AUTO]
REF Cycle Time 110 [110]
WRITE Recovery Time 15 [15]
READ to PRE Time 9 [9]
FOUR ACT WIN Time 31 [31]
Back-To-BackCAS# Delay 0 [Auto]
Timing Mode 1N [1N]
Round Trip Latency on CHA [AUTO]
Round Trip Latency on CHB [AUTO]
Round Trip Latency on CHC [AUTO]
WRITE To READ Delay(DD) 8 [Auto]
WRITE To READ Delay(DR) 8 [Auto]
WRITE To READ Delay(SR) 18 [Auto]
READ To WRITE Delay(DD) 7 [Auto]
READ To WRITE Delay(DR) 7 [Auto]
READ To WRITE Delay(SR) 7 [Auto]
READ To READ Delay(DD) 7 [Auto]
READ To READ Delay(DR) 6 [Auto]
READ To READ Delay(SR) 4 [Auto
]WRITE To WRITE Delay(DD) 8 [Auto]
WRITE To WRITE Delay(DR) 8 [Auto]
WRITE To WRITE Delay(SR) 18 [Auto]
CPU Differential Amplitude [Auto]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
Extreme Engine Digi
Digi+ PWR Mode [T-Balanced]
PWR Volt. Control [Auto]
Load-Line Calibration [Full]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [1000kHz]
Extreme OV [Disabled]
Extreme OC [Auto]
CPU Voltage 1.250 [1.25000]
CPU PLL Voltage 1.812 [Auto]
QPI/DRAM Core Voltage 1.350 [1.35000]
DRAM Bus Voltage 1.654 [Auto]
>DRAM REF Voltages
DRAM DATA REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM DATA REF Voltage on CHB [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHC [Auto]
DRAM CTRL REF Voltage on CHC [Auto]
IOH Voltage 1.244 [Auto]
IOH PCIE Voltage 1.508 [Auto]
ICH Voltage 1.111 [Auto]
ICH PCIE Voltage [Auto
]
Spread Spectrum Control
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
***on-board jumper dependant
شكرا لك لكن كيف اقوم بادخالها
Ahmed Elbrbry
17-04-2011, 22:17
حضرتك مش هتدخل اى قيمة من هنا
لكن لو اى عضو قالك مثلا ارفع الفولت
هتعرف الفولت بيترفع منين
اكيد لازم يكون معاك نسخة من ال BIOS
ديه بقى نسخة من ال BIOS بتاع لوحتك لتسهيل
لو اى عضو شرحلك معولمة وانت مش عارفها ممكن يقولك توصلها ازاى من خلال هذا القالب
كدة تمام
المستبسل
20-04-2011, 14:15
وعليكم السلام ورحمة الله وبركاته
الحرارة لديك لن تسمح لك بالوصول لكسر سرعة عالي ، كذلك عدد الرامات لديك سيحد من إمكانية كسر السرعة العالي
المعالج بفولت جيد ، لكنك لم تحدد حدود الكسر الذي ترغب الوصول إليه
مبدئياً هذه الإعدادات التي تحتاج تغييرها لكسر السرعة لحدود 4.2MHz ، لكن أنصحك بتشغيل التكييف قبل تجربة الإعدادت حتى نتأكد في حالة فشل كسر السرعة من أن المشكلة ليست من الحرارة
Target CPU Frequency 4200MHz
Target DRAM Frequency 1600MHz
QPI Loadline Calibration Enabled
CPU Ratio Setting 26
CPU Configuration
C1E Support [Disabled]
CPU TM Function [Disabled]
Intel(R) HT Technology [Enabled]
Active Processor Cores [All]
Intel(R) SpeedStep(TM) Tech [Disabled]
Intel(R) C-STATE Tech [Disabled]
BCLK Frequency [160]
PCIE Frequency [100]
DRAM Frequency [1600]
UCLK Frequency [Auto]
>
DRAM Timing Control
CAS# Latency 9 [8]
RAS# to CAS# Delay 9 [8]
RAS# PRE Time 9 [8]
RAS# ACT Time 24 [24]
Load-Line Calibration [Full]
CPU Voltege OCP [Enabled]
Extreme OC [Auto]
CPU Voltage 1.250 [1.35]
CPU PLL Voltage 1.812 [Auto]
QPI/DRAM Core Voltage 1.33 [1.33]
DRAM Bus Voltage 1.654 [1.65]
IOH Voltage 1.244 [Auto]
IOH PCIE Voltage 1.508 [Auto]
ICH Voltage 1.111 [Auto]
ICH PCIE Voltage [Auto
شكرا لك على الرد
وانا اشوف الحرار
ان شاء الله بجرب
Gainward
20-04-2011, 22:44
ارغب بالوصول 4000
طبق نفس الأعدادات التي أعطاها لك أخونا خالد "المستبسل" مع تقليل معامل ضرب المعالج "CPU Raito Setting" الى 25
mahdi611
22-04-2011, 14:45
اخي العزيز كودمان مبدئيا كونك مبتدئ فقط ارفع CPU Ratio Setting الى 30 وال BCLK Frequency الى 134
وفولت المعالج cpu vcore الى 1.32
هذه ابسط طريقه للمحافظه على جميع الاعدادات كما هي باستثناء كسر سرعة المعالج
اليك BIOS TEMPLATE للوحة الخاصة بك
لتسهيل التعامل مع المسطلحات
Target CPU Frequency 2666MHz
Target DRAM Frequency 1603MHz
LN2 Mode: Disabled***
QPI Loadline Calibration: Enabled
***Sync Mode [Enabled]
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [20.0]
CPU Turbo Power Limit [Disabled]
CPU Configuration
CPU Ratio Setting [20.0]
C1E Support [Enabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetcher [Enabled]
Intel(R) Virtualiyation Tech [Enabled]
CPU TM Function [Disabled]
Execute Disable Bit [Enabled]
Intel(R) HT Technology [Enabled]
Active Processor Cores [All]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Enabled]
Intel(R) C-STATE Tech [Enabled]
C State package limit setting [Auto]
BCLK Frequency [133]
PCIE Frequency [100]
DRAM Frequency [1603]
UCLK Frequency [3209]
QPI Link Data Rate [AUTO]
Memory Configuration Protect [Disabled]
>
DRAM Timing Control
CAS# Latency 9 [9]
RAS# to CAS# Delay 9 [9]
RAS# PRE Time 9 [9]
RAS# ACT Time 24 [24]
RAS# to RAS# Delay 6 [AUTO]
REF Cycle Time 110 [110]
WRITE Recovery Time 15 [15]
READ to PRE Time 9 [9]
FOUR ACT WIN Time 31 [31]
Back-To-BackCAS# Delay 0 [Auto]
Timing Mode 1N [1N]
Round Trip Latency on CHA [AUTO]
Round Trip Latency on CHB [AUTO]
Round Trip Latency on CHC [AUTO]
WRITE To READ Delay(DD) 8 [Auto]
WRITE To READ Delay(DR) 8 [Auto]
WRITE To READ Delay(SR) 18 [Auto]
READ To WRITE Delay(DD) 7 [Auto]
READ To WRITE Delay(DR) 7 [Auto]
READ To WRITE Delay(SR) 7 [Auto]
READ To READ Delay(DD) 7 [Auto]
READ To READ Delay(DR) 6 [Auto]
READ To READ Delay(SR) 4 [Auto
]WRITE To WRITE Delay(DD) 8 [Auto]
WRITE To WRITE Delay(DR) 8 [Auto]
WRITE To WRITE Delay(SR) 18 [Auto]
CPU Differential Amplitude [Auto]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
Extreme Engine Digi
Digi+ PWR Mode [T-Balanced]
PWR Volt. Control [Auto]
Load-Line Calibration [Full]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [1000kHz]
Extreme OV [Disabled]
Extreme OC [Auto]
CPU Voltage 1.250 [1.25000]
CPU PLL Voltage 1.812 [Auto]
QPI/DRAM Core Voltage 1.350 [1.35000]
DRAM Bus Voltage 1.654 [Auto]
>DRAM REF Voltages
DRAM DATA REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM DATA REF Voltage on CHB [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHC [Auto]
DRAM CTRL REF Voltage on CHC [Auto]
IOH Voltage 1.244 [Auto]
IOH PCIE Voltage 1.508 [Auto]
ICH Voltage 1.111 [Auto]
ICH PCIE Voltage [Auto
]
Spread Spectrum Control
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
***on-board jumper dependant
كيف استخدمة
اخي العزيز كودمان مبدئيا كونك مبتدئ فقط ارفع CPU Ratio Setting الى 30 وال BCLK Frequency الى 134
وفولت المعالج cpu vcore الى 1.32
هذه ابسط طريقه للمحافظه على جميع الاعدادات كما هي باستثناء كسر سرعة المعالج
غيرت المطلوب لكن اين اجد
BCLK Frequency
mahdi611
23-04-2011, 00:15
اذا ما لقيتوش خلاص خلليه كما هو 133 بطبيعته واعمل حفظ ورستارت وشوف درجات الحراره ماشيه مع الكسر ولا عاليه
شكرا لك عزيزي لقيت الخيار وعدلته بس اللوحه لما عملت حفظ لها ورستار
عملت رستار وطلبت مني اما اعدل الاعدادات او اعمل ديفوت للاعدادات
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved, TranZ by Almuhajir