مشاهدة النسخة كاملة : رسالة خطأ تظهر عند تشغيل الراوتر
رسالة خطأ تظهر عند تشغيل الراوتر
2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Readonly ROMMON initialized
boot: cannot determine first executable file name on device "flash:"
c2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Readonly ROMMON initialized
boot: cannot determine first executable file name on device "flash:"
c2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Readonly ROMMON initialized
rommon 1 >
طبعا حاولت كتب الأمر reset
ترجع نفس الرسالة
طلعت الفلاش وركبته مرة ثانية نفس الشيء
ارجوا المساعدة
nubianzerocool
21-11-2011, 22:36
الروتر مش قادر يوصل لملف IOS
أتأكد من الملف في الفلاش
rommon 1> dir flash:
لو موجود حاول تبوت منه
rommon 2 > boot flash:أسم الملف
لو الملف مش موجود أو مش شغال و المشكلة أستمرت وده اللي حاصل في الغالب
هتغير قيم Registery File
بحيث أنها تتجاهل البوت من الفلاش و تبدي من ROM
من Rx-boot
هتستخدم القيمة 0x2101
rommon 1 > confreg 0x2101
و أعمل Reset
rommon 2>reset
طيب بعد أخر خطوة وهي أعادة التشغيل هل يرجع الراوتر إلى طبيعته بمعنى سوف يكون هناك نظام ؟
أنا كنت أخذت باكب من ios باستخدام برنامج cisco tftp server هل ممكن أقدر أرجع النسخة هذه على الفلاش وشكرا ؟؟؟
nubianzerocool
21-11-2011, 23:39
بعد أعادة التشغيل الروتر هيشتغل من
Rxboot Mode
router(boot)>و منها تقدر تعمل ريستور للنسخة الليأنت واخدها علي سيرفير tftp
في وضع
router(boot)>
j
هل يعمل أمر
copy tftp: flash:
j
يعني أنت عارف لازم نقوم بإعداد ip المنافذ لكي يستطيع tftp server على الجهاز الكمبيوتر أن يعمل
أن شاء الله بكرة بأطبق كلامك وأرد عليك مشكور ما قصرت
لم يصلح الحال وبحث في النت ولقيت الطريقة التالية وأيضا لم يصلح الحال
ارجوا المساعدة
Router - Installing IOS onto new FLASH (https://www.fir3net.com/Router/Cisco-Router/installing-ios-onto-a-new-flash.html)
Router - Cisco Router
Sunday, 18 May 2008 13:33
You will need to first install the flash module into the device. Then run the following commands via the console port (rommon), to check your systems resources for the install. rommon 1 > dev
rommon 2 > meminfo Then to copy it from your tftp server...rommon 3 > IP_ADDRESS=192.168.4.1
rommon 4 > IP_SUBNET_MASK=255.255.255.0
rommon 5 > DEFAULT_GATEWAY=192.168.4.100
rommon 6 > TFTP_SERVER=172.16.1.88
rommon 7 > TFTP_FILE=c2600-i-mz.123-4.bin
rommon 8 > tftpdnld
IP_ADDRESS: 192.168.4.1
IP_SUBNET_MASK: 255.255.255.0
DEFAULT_GATEWAY: 192.168.4.100
TFTP_SERVER: 172.16.1.88
TFTP_FILE: c2600-i-mz.122-12.bin
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash will be lost!
Do you wish to continue? y/n: [n]: y
.
Receiving c2600-i-mz.123-4.bin from 172.16.1.88 !!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!
File reception completed.
Copying file c2600-i-mz.123-4.bin to flash.
Erasing flash at 0x60ac0100
program flash location 0x6052190
rommon 9 > dir flash:
rommon 10 > confreg 0x2101
rommon 11 > reset
nubianzerocool
24-11-2011, 01:44
أنا أسف علي أستمرا المشكلة
لكن ممكن تقولي لما غيرت قيم الريجيستري
أيه اللي حصل
تجاهل البوت من الفلاش و بوت من الروم
Router (boot)
و لا لأ
و لا عديت الخطوة دي و معرفتش تعمل ريستور
يا ريت توضح أيه اللي حصل معاك
غيرت لي 0x2101
وما نفع لما أعمل reset
يرجع بنفس الرسالة الاولى في المشاركة
2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Readonly ROMMON initialized
boot: cannot determine first executable file name on device "flash:"
c2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Readonly ROMMON initialized
boot: cannot determine first executable file name on device "flash:"
c2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Readonly ROMMON initialized
rommon 1 >
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved, TranZ by Almuhajir