مشكلة فى ال password recovery على راوتر cisco 7600

[Dr Virus.exe]

السلام عليكم
عندى اروتر سسكو 7600 مش عارف باسورد ال enable secret
قلت لحالى اعمل password recovery
دخلت على الrommon
و كتبت
confreg 0x2142
reset
و لكن لالااسف الراوتر بيطلب منى باسورد لل enable secret
لاحظ انا ممكن افوت على ال User mode لانى بأعرف الباسورد و لما اكتب الامر sh ver

NS-Gateway>sh version
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(1)S, RELEASE SOFTWARE (fc1)
Technical Support: https://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Sun 27-Nov-11 15:27 by prod_rel_team

ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(1)S, RELEASE SOFTWARE (fc1)

NS-Gateway uptime is 1 hour, 27 minutes
Uptime for this control processor is 1 hour, 28 minutes
System returned to ROM by power-on (SP by power-on)
System image file is "sup-bootdisk:c7600s3223-adventerprisek9-mz.152-1.S.bin"
Last reload type: Normal Reload
Last reload reason: power-on



This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
https://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco CISCO7604 (R7000) processor (revision 2.0) with 458752K/65536K bytes of memory.
Processor board ID FOX1509G2DK
R7000 CPU at 300MHz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
1 Virtual Ethernet interface
9 Gigabit Ethernet interfaces
1915K bytes of non-volatile configuration memory.

65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102



لاحظ فى الاسفل انو ال config register مازال 0x2102 مع انى متأكد انى كتبتو 0x2142 جربت اكتر من مرة و نفس المشكلة .... جربت احط ال config resiter 0x2100 قلت يمكن 0x2142 نحس :D:D:D:D
نفس المشكلة , دورت فى النت و فى مواقع سسكو ما لقيت حل للموضوع

ارجو المساعدة فى حل هذه المشكلة , لانى الى حوالى اكتر من 5 ساعات و انا بحاول احل المشكلة

و على فكرة , الاروتر لما يقوم بياخد حوالى 12 دقيقة عبال ما يشتغل و يصير up :eek::eek::eek:

يعنى وقت كتيييييييير:):):):)

فى الانتظار يا شباب




شكرا

[sheno]

first of all : all your procedure is perfect

so try to instead of type the comamnd ( reset ) instead press the power off and power on for your device
may be it makes diffrence

[Dr Virus.exe]

first of all : all your procedure is perfect

so try to instead of type the comamnd ( reset ) instead press the power off and power on for your device
may be it makes diffrence

welcome bro ,
i would like to say that i could finally solve thiss issue ,

the problem was because i just press break after powering up the router , and the right decisiion was to wait until the router process start to work then press break
this issue mean that there are two processors, one for switch when i power it on, and the 2nd one after normally 10 minutes
and the soltuion was done after booting from router processor
any way
thansk 0ll
reagrds

[sheno]

مبروك يا غالى ومزيدا من التوفيق