مشاهدة النسخة كاملة : سؤال فى ال debug
Dr Virus.exe
02-11-2012, 12:55
السلام عليكم
انا عامل عندى route على null0 interface علشان امنع ال loop
الان ملاحظ من ال snmp عندى انو وصل ال traffic على ال null0 interface حوالى 1 ميجا !!!!!!!!!!
يعنى نسبة مش قليلة .......ز الان انا من الراوتر بدى اشوف ايش بيصير على هادا ال null 0 interface
رحت عملت:
R1#debug interface null 0
Condition 1 set
R1#sh debugging
Condition 1: interface Nu0 (1 flags triggered)
Flags: Nu0
R1#
بس لحتى الام ما طلع اشى فى ال CONSOLE
ناا شابك تلنت و عملت
TERMINLA MONITOR
بس برضو ما طلع اشى فى ال CONSOLE TERMINAL عندى ؟؟!!!
حدا مر علهي هادا الموضوع؟
ايه هو الcondition 1 set?
Dr Virus.exe
02-11-2012, 14:47
ايه هو الcondition 1 set?
مهوة هادا اللى انا مش فاهمو !!!
مش عارف ايش هو ال CONDITION 1
??
!
بسم الله والحمد لله والصلاة والسلام علي رسول الله وآله وصحبه وإخوانه وسلم:
الكوندشن ده علشان يعرض الباكيت الخاصة بالانترفيس النل فقط، انت ممكن تشوف الكونديشن
R1#show debug condition
Condition 1: interface Nu0 (1 flags triggered)
Flags: Nu0
وممكن تلغيه
R1#no debug condition 1
This condition is the last interface condition set.
Removing all conditions may cause a flood of debugging
messages to result, unless specific debugging flags
are first removed.
Proceed with removal? [yes/no]:
عامة اقرا شوية في الcondtional debug
وصلي الله وسلم وبارك علي النبي وآله وصحبه وإخوانه وسلم
Dr Virus.exe
04-11-2012, 10:08
بسم الله والحمد لله والصلاة والسلام علي رسول الله وآله وصحبه وإخوانه وسلم:
الكوندشن ده علشان يعرض الباكيت الخاصة بالانترفيس النل فقط، انت ممكن تشوف الكونديشن
R1#show debug condition
Condition 1: interface Nu0 (1 flags triggered)
Flags: Nu0
وممكن تلغيه
R1#no debug condition 1
This condition is the last interface condition set.
Removing all conditions may cause a flood of debugging
messages to result, unless specific debugging flags
are first removed.
Proceed with removal? [yes/no]:
عامة اقرا شوية في الcondtional debug
وصلي الله وسلم وبارك علي النبي وآله وصحبه وإخوانه وسلم
لو لغيت ال condition بياتغى ال DEBUG نفسو معاه !!!!
شوف هنا :
=================
Switch#debug interface fastEthernet 0/1
Condition 1 set
Switch#sh debugging
Condition 1: interface Fa0/1 (1 flags triggered)
Flags: Fa0/1
Switch#no debug condition 1
This condition is the last interface condition set.
Removing all conditions may cause a flood of debugging
messages to result, unless specific debugging flags
are first removed.
Proceed with removal? [yes/no]: y
Condition 1 has been removed
Switch#sh debugging
Switch#
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved, TranZ by Almuhajir