blackbird1983
18-02-2013, 23:21
السلام عليكم
اولا احب اشكر كل اعضاء النتدى الكريم لانى فعلا استفدت منه كتير جدا و ربنا يكرم المشرفين عليه و يجازيهم كل خير ان شاء الله.
انا عملت لاب pagp على cisco iou on unix بس مش شغال معايا.
اللاب بسيط جدا عبارة عن سويتشين واصلين ببعض ب 4 بورتات و ده صور من ال output
اللاب
1001:e0/0 1002:e0/0
1001:e0/1 1002:e0/1
1001:e0/2 1002:e0/2
1001:e0/3 1002:e0/3
-----------------------------------------------------
SW1#sh run
interface Port-channel10
switchport
!
interface Ethernet0/0
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/2
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/3
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Vlan1
no ip address
shutdown
!
!
--------------------------------------------
SW2#sh run
interface Port-channel10
switchport
!
interface Ethernet0/0
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/2
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/3
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Vlan1
no ip address
shutdown
!
----------------------------------------------------
SW1#sh etherchannel summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use N - not in use, no aggregation
f - failed to allocate aggregator
M - not in use, no aggregation due to minimum links not met
m - not in use, port not aggregated due to minimum links not met
u - unsuitable for bundling
d - default port
w - waiting to be aggregated
Number of channel-groups in use: 1
Number of aggregators: 1
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
10 Po10(SD) PAgP Et0/0(D) Et0/1(D) Et0/2(D)
Et0/3(D)
--------------------------------------
sw2#sh etherchannel su
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use N - not in use, no aggregation
f - failed to allocate aggregator
M - not in use, no aggregation due to minimum links not met
m - not in use, port not aggregated due to minimum links not met
u - unsuitable for bundling
d - default port
w - waiting to be aggregated
Number of channel-groups in use: 1
Number of aggregators: 1
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
10 Po10(SD) PAgP Et0/0(D) Et0/1(D) Et0/2(D)
Et0/3(D)
-------------------------------------------------------------------
SW1#sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port ID
sw2 Eth 0/0 171 R S Linu Eth 0/0
sw2 Eth 0/1 135 R S Linu Eth 0/1
sw2 Eth 0/2 166 R S Linu Eth 0/2
sw2 Eth 0/3 166 R S Linu Eth 0/3
SW1#SW1#sh cdp nei
--------------------------------------------------------------
sw2#sh cdp ne
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port ID
SW1 Eth 0/3 168 R S Linu Eth 0/3
SW1 Eth 0/2 175 R S Linu Eth 0/2
SW1 Eth 0/1 157 R S Linu Eth 0/1
SW1 Eth 0/0 163 R S Linu Eth 0/0
----------------------------------------------------
SW1#sh ip int br
Interface IP-Address OK? Method Status Protocol
Ethernet0/0 unassigned YES unset up up
Ethernet0/1 unassigned YES unset up up
Ethernet0/2 unassigned YES unset up up
Ethernet0/3 unassigned YES unset up up
Port-channel10 unassigned YES unset down down
Vlan1 unassigned YES manual up up
------------------------------------------------------------------
sw2#sh ip int br
Interface IP-Address OK? Method Status Protocol
Ethernet0/0 unassigned YES unset up up
Ethernet0/1 unassigned YES unset up up
Ethernet0/2 unassigned YES unset up up
Ethernet0/3 unassigned YES unset up up
Port-channel10 unassigned YES unset down down
Vlan1 unassigned YES unset up up
----------------------------------
كل حاجة شغالة ماعدا port-channel عملتلها no shut وبرده مش شغالة.
هل فى حاجة حاجة نافصة ؟؟؟
انا قريت الموضوع بتاع البشمهندس جواد
https://arabhardware.net/forum/showthread.php?t=315520
كان فى زميل عنده مشكلة فى pagp و عملت اللى هو عمله بس برده متعملتش.
ارجو المساعدة .
متشكر جداا
اولا احب اشكر كل اعضاء النتدى الكريم لانى فعلا استفدت منه كتير جدا و ربنا يكرم المشرفين عليه و يجازيهم كل خير ان شاء الله.
انا عملت لاب pagp على cisco iou on unix بس مش شغال معايا.
اللاب بسيط جدا عبارة عن سويتشين واصلين ببعض ب 4 بورتات و ده صور من ال output
اللاب
1001:e0/0 1002:e0/0
1001:e0/1 1002:e0/1
1001:e0/2 1002:e0/2
1001:e0/3 1002:e0/3
-----------------------------------------------------
SW1#sh run
interface Port-channel10
switchport
!
interface Ethernet0/0
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/2
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/3
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Vlan1
no ip address
shutdown
!
!
--------------------------------------------
SW2#sh run
interface Port-channel10
switchport
!
interface Ethernet0/0
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/2
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Ethernet0/3
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
duplex auto
channel-protocol pagp
channel-group 10 mode desirable non-silent
!
interface Vlan1
no ip address
shutdown
!
----------------------------------------------------
SW1#sh etherchannel summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use N - not in use, no aggregation
f - failed to allocate aggregator
M - not in use, no aggregation due to minimum links not met
m - not in use, port not aggregated due to minimum links not met
u - unsuitable for bundling
d - default port
w - waiting to be aggregated
Number of channel-groups in use: 1
Number of aggregators: 1
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
10 Po10(SD) PAgP Et0/0(D) Et0/1(D) Et0/2(D)
Et0/3(D)
--------------------------------------
sw2#sh etherchannel su
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use N - not in use, no aggregation
f - failed to allocate aggregator
M - not in use, no aggregation due to minimum links not met
m - not in use, port not aggregated due to minimum links not met
u - unsuitable for bundling
d - default port
w - waiting to be aggregated
Number of channel-groups in use: 1
Number of aggregators: 1
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
10 Po10(SD) PAgP Et0/0(D) Et0/1(D) Et0/2(D)
Et0/3(D)
-------------------------------------------------------------------
SW1#sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port ID
sw2 Eth 0/0 171 R S Linu Eth 0/0
sw2 Eth 0/1 135 R S Linu Eth 0/1
sw2 Eth 0/2 166 R S Linu Eth 0/2
sw2 Eth 0/3 166 R S Linu Eth 0/3
SW1#SW1#sh cdp nei
--------------------------------------------------------------
sw2#sh cdp ne
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port ID
SW1 Eth 0/3 168 R S Linu Eth 0/3
SW1 Eth 0/2 175 R S Linu Eth 0/2
SW1 Eth 0/1 157 R S Linu Eth 0/1
SW1 Eth 0/0 163 R S Linu Eth 0/0
----------------------------------------------------
SW1#sh ip int br
Interface IP-Address OK? Method Status Protocol
Ethernet0/0 unassigned YES unset up up
Ethernet0/1 unassigned YES unset up up
Ethernet0/2 unassigned YES unset up up
Ethernet0/3 unassigned YES unset up up
Port-channel10 unassigned YES unset down down
Vlan1 unassigned YES manual up up
------------------------------------------------------------------
sw2#sh ip int br
Interface IP-Address OK? Method Status Protocol
Ethernet0/0 unassigned YES unset up up
Ethernet0/1 unassigned YES unset up up
Ethernet0/2 unassigned YES unset up up
Ethernet0/3 unassigned YES unset up up
Port-channel10 unassigned YES unset down down
Vlan1 unassigned YES unset up up
----------------------------------
كل حاجة شغالة ماعدا port-channel عملتلها no shut وبرده مش شغالة.
هل فى حاجة حاجة نافصة ؟؟؟
انا قريت الموضوع بتاع البشمهندس جواد
https://arabhardware.net/forum/showthread.php?t=315520
كان فى زميل عنده مشكلة فى pagp و عملت اللى هو عمله بس برده متعملتش.
ارجو المساعدة .
متشكر جداا